indicators not working

Technical discussions
Post Reply
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

indicators not working

Post by duncan »

its not the fuse I have checked that :D anyone got any other ideas and how to locate the issue?

anyone know where the relay is?
Top
IWANT1
Posts: 2832
Joined: Fri Jul 28, 2006 9:26 pm
Location: cambridgeish

Post by IWANT1 »

Should i bring a multimeter :lol:
Image
" Uh Betty you should of seen this car in Ely today!! it had stickers and stripes
all over it, and when it started up, the noise!!!, I could feel my teeth rattling!!!"
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

IWANT1 wrote:Should i bring a multimeter :lol:
erm - it might come in handy :D

Cheers mate :thumb:
Top
User avatar
ScoobieWRX
Posts: 2136
Joined: Tue Jul 31, 2007 9:42 am
Location: Northants
Contact:
Contact ScoobieWRX

Post by ScoobieWRX »

The relay is under the dash in the same vicinity as the clutch and brake switches just above the pedals. Look above the Clutch/Brake pedal you should see a black connector which has the Turn & Hazard light Module (Relay) plugged into it.

It's a pity the indicators aren't working, you could hear it clicking away then to locate it easily. Have you tried the Hazard switch so all indicators come on and off as it's all on the same circuit.

See pic below - connector B32 is the connector you're looking for in the grayed out box. The illustration is form a left hand drive STi so you should be able to work it out from there.

Image
Buggers cancelled my op just a couple of days before it was due. Inconsiderate barstewards!! :rant:

Image

Waiting now for another execution date!!:headhack:
Top
User avatar
frayz
Posts: 1567
Joined: Tue Oct 24, 2006 11:23 am
Location: Frayz-Engineering HQ, Essex

Post by frayz »

Dunc, MAKE SURE THE MULTIPLUG HASNT COME OUT OF THE HAZZARD WARNING SWITCH. THE INDICATORS WILL NOT WORK IF THIS HAS BEEN UNPLUGGED.
Whoops sorry for the capps
Frayz-Engineering Prodrive edition V7 STi
Built 2.5L, custom heads, GT35R, T-Logic, Tial, Fuelab, Injector Dynamics, GT-Spec, Exedy Compe R, Innovate, APS, KW, AP Racing, Whiteline, Noltec, Sparco, Speedline & S.R.E.
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

Cheers chaps - will try it out.

Hazards dont work either (nor the remote locking flashing of the indicators)
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

Sorted.

No idea how I did it but the indicators just starting working again :D

The fuse for the hazards had blown though :lol:

Bloody oil :pmsl:
Top
User avatar
ScoobieWRX
Posts: 2136
Joined: Tue Jul 31, 2007 9:42 am
Location: Northants
Contact:
Contact ScoobieWRX

Post by ScoobieWRX »

I bet you're glad now you didn't have to fiddle around under the dash :D

Nothing worse than wiring..... :lol:
Buggers cancelled my op just a couple of days before it was due. Inconsiderate barstewards!! :rant:

Image

Waiting now for another execution date!!:headhack:
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

I hate wiring :D






and oil :D

Apart from that, this whole car tuning thing is easy peezy :lol:
Top
Post Reply

Return to “Technical queries”