Now she looks like a drift racer, ha ha ha

Photo Gallery
Post Reply
User avatar
frayz
Posts: 1567
Joined: Tue Oct 24, 2006 11:23 am
Location: Frayz-Engineering HQ, Essex

Now she looks like a drift racer, ha ha ha

Post by frayz »

Had a little fiddle about with this this morning.

Just a dummy run so i can get everything sitting right, cut the relevant areas etc, get the spare bumper cut and then get it all painted.

To say this thing is rather large is a little understatement and it looks like it will take 10bar lol

Sorry for the fone pics, but thought the weather was too nice not to take a few. :D

Image
Image
Image
Image
Image
Image
Image
Frayz-Engineering Prodrive edition V7 STi
Built 2.5L, custom heads, GT35R, T-Logic, Tial, Fuelab, Injector Dynamics, GT-Spec, Exedy Compe R, Innovate, APS, KW, AP Racing, Whiteline, Noltec, Sparco, Speedline & S.R.E.
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

which hole does your induction kit go in frayz?
Top
User avatar
frayz
Posts: 1567
Joined: Tue Oct 24, 2006 11:23 am
Location: Frayz-Engineering HQ, Essex

Post by frayz »

Its not a problem Dunc as i have a brand new APS 70mm waiting to go on too. :D
Frayz-Engineering Prodrive edition V7 STi
Built 2.5L, custom heads, GT35R, T-Logic, Tial, Fuelab, Injector Dynamics, GT-Spec, Exedy Compe R, Innovate, APS, KW, AP Racing, Whiteline, Noltec, Sparco, Speedline & S.R.E.
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

:thumb:

Make sure you mount the hoses onto the bottom fitting of the fmic left hand side as far on as you can so that they dont push the CAI onto the wheel arch liner. It can cause it to rub against the wheel.

I used an extra 100mm length of silicone to space the CAI filter down into the arch a bit more to give it more room. There may be no problem on yours but worth checking.
Top
User avatar
frayz
Posts: 1567
Joined: Tue Oct 24, 2006 11:23 am
Location: Frayz-Engineering HQ, Essex

Post by frayz »

Cheers for the tip buddy, any advise is always appreciated.

I have spare hose if need be.
Frayz-Engineering Prodrive edition V7 STi
Built 2.5L, custom heads, GT35R, T-Logic, Tial, Fuelab, Injector Dynamics, GT-Spec, Exedy Compe R, Innovate, APS, KW, AP Racing, Whiteline, Noltec, Sparco, Speedline & S.R.E.
Top
mike-payne
Posts: 729
Joined: Sat Oct 21, 2006 4:30 pm
Contact:
Contact mike-payne

Post by mike-payne »

frayz wrote:Cheers for the tip buddy, any advise is always appreciated.

I have spare hose if need be.
looking good..... now build that bloody engine!!!!
Take regular exercise, walk to you car!
Top
User avatar
frayz
Posts: 1567
Joined: Tue Oct 24, 2006 11:23 am
Location: Frayz-Engineering HQ, Essex

Post by frayz »

Patience my dear boy...

:-D
Frayz-Engineering Prodrive edition V7 STi
Built 2.5L, custom heads, GT35R, T-Logic, Tial, Fuelab, Injector Dynamics, GT-Spec, Exedy Compe R, Innovate, APS, KW, AP Racing, Whiteline, Noltec, Sparco, Speedline & S.R.E.
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

mike-payne wrote:
frayz wrote:Cheers for the tip buddy, any advise is always appreciated.

I have spare hose if need be.
looking good..... now build that bloody engine!!!!
:lol:
Top
User avatar
ScoobieWRX
Posts: 2136
Joined: Tue Jul 31, 2007 9:42 am
Location: Northants
Contact:
Contact ScoobieWRX

Post by ScoobieWRX »

I could swear your car is grinning!! :grin:

Nice one :thumb:
Buggers cancelled my op just a couple of days before it was due. Inconsiderate barstewards!! :rant:

Image

Waiting now for another execution date!!:headhack:
Top
User avatar
duncan
Posts: 10897
Joined: Thu Jul 27, 2006 3:12 pm
Location: On the podium
Contact:
Contact duncan

Post by duncan »

frayz - did you weigh the std bumper bar on yours?
Top
Post Reply

Return to “Photos”